英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字,中文词皆可:

unbefitting    
a. 不合适的,不相宜的

不合适的,不相宜的

unbefitting
adj 1: not befitting; "behavior unbefitting a father"

Unbefitting \Unbefitting\
See {befitting}.

82 Moby Thesaurus words for "unbefitting":
bad, futile, ill-adapted, ill-advised, ill-assorted, ill-chosen,
ill-considered, ill-fitted, ill-matched, ill-seasoned, ill-sorted,
ill-suited, ill-timed, impolitic, improper, inadmissible,
inadvisable, inapplicable, inapposite, inappropriate, inapt,
inauspicious, incongruous, inconvenient, inept, inexpedient,
infelicitous, inopportune, intempestive, intrusive, irrelevant,
late, mal a propos, maladjusted, malapropos, misjoined, mismatched,
mismated, misplaced, mistimed, off base, out of character,
out of joint, out of keeping, out of line, out of phase,
out of place, out of proportion, out of season, out of time,
out of tune, premature, too late, too soon, unadapted, unapt,
unbecoming, uncomely, undesirable, undue, unfavorable, unfit,
unfitted, unfitting, unfortunate, unhandy, unhappy, unlucky,
unmeet, unprofitable, unpropitious, unqualified, unready, unripe,
unseasonable, unseemly, unsuitable, unsuited, untimely, untoward,
unwise, wrong


请选择你想看的字典辞典:
单词字典翻译
unbefitting查看 unbefitting 在百度字典中的解释百度英翻中〔查看〕
unbefitting查看 unbefitting 在Google字典中的解释Google英翻中〔查看〕
unbefitting查看 unbefitting 在Yahoo字典中的解释Yahoo英翻中〔查看〕





安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • CUTWATER? | Eng-Tips
    The "cutwater" is located in the discharge casing of a centrifugal pump and it directs the product discharge from the impeller into the discharge volute Along with the impeller, the cutwater can suffer damage from cavitation
  • cutwater | Eng-Tips
    Hello Does anybody know where I can get an information about the shape of cutwater in the centrifugal pumps and its influence on vane-pass frequency? Thanks
  • Aluminum ramps | Eng-Tips
    I am seeking recommendations for Aluminum ramp vendors in Texas I have a project that I am working on that is using an aluminum ramp I have been asked to determine an Aluminum Ramp vendor to be recommended to the contractor form them to use Comments suggestions are appreciated
  • Purpose of thickened edge for concrete slabs on grade?
    Good Afternoon, I'd appreciate guidance on what the purpose is of a thickened edge for slabs on grade as well as what the design process looks like Many thanks for your help!
  • DESIGN MARGIN | Eng-Tips
    Depends on what you mean by "design capacity" Sometimes, the design flow already has a margin over annual average This margin over annual average would account for time taken for annual shutdown, other unexpected trips, surges in flow etc This is for the process plant For utilities, the sum total of design margins for each utility must generally reflect the design margins used for the
  • Thrust Load on Braided Flex Hose | Eng-Tips
    A braided hose acts like a tied expansion joint with the braid acting as the tie rods Therefore, there is not any pressure thrust load on the anchor
  • Abaqus Standard errors | Eng-Tips
    Hello everyone, I am trying to solve a series of problems I am experiencing using Abaqus Standard to run my simulations Every single simulation is interrupted by one of these errors in several steps: *** ABAQUS standard rank 0 encountered a SEGMENTATION FAULT*** ERROR CATEGORY: ORDERING ***
  • Effects of worn cutwater throat in pump | Eng-Tips
    Hi everyone, I have been searching online for information about the effects of a worn cutwater throat in pumps but have not been too sucessful Can anyone help ? Thanks alot
  • ASME BPVC Section III Div 1 Subsections ND and NCD | Eng-Tips
    Hi, Could someone please explain what the difference is between ASME BPVC Section III Division 1 Subsection NCD 2023 and ASME BPVC Section III Division 1
  • How do I copy and paste drawings while keeping full dimensions model . . .
    Good morning all, I am quite new to Creo (for my new job) and had a quick question about copying and pasting drawing views dimensions I have a drawing that has a model with dimensions on it I want to copy the model dimensions notes and paste it to a separate sheet Previous methods I have





中文字典-英文字典  2005-2009